Andersson LED2242FDC PVR Manual de usuario descargar pdf (Pagina 29)

English - 28 -

Set Timer / Delete Timer

After you have selected a programme in the EPG

menu, press the OK button. Select the Set Timer

on Event option and press the OKbutton.Youcan

set a timer for future programmes. To cancel an

already set timer, highlight that programme and

press the OK button. Then select “Delete Timer”

option. The timer will be cancelled.

Note: It is not possible to record two channels at the

same time..Software Upgrade

Your TV is capable of finding and updating

automatically via the Aerial/Cable signal or over the

Internet.

Software upgrade search via user

interface

Simply navigate on your main menu. Choose

Settings and select Other Settings menu.

In Other Settings menu navigate on to the

Software for Upgrade item and press OK

button to check for a new software upgrade.

Note : Internet connection is needed. If an internet

connection is not available, try to upgrade via

broadcast. If a new upgrade is found, it starts

todownloadtheupgrade.PressOK to continue

with the reboot operation.

3 AM search and upgrade mode

While the TV is connected to an aerial signal. If

Automatic scanning in the Upgrade Options menu

is enabled, the TV wakes up at 03:00 and searches

broadcast channels for new software upgrades. If

new software is found and downloaded successfully,

the next time the TV powers up , it will have the new

software version.

Note: If the TV fails to come on after the upgrade unplug the

TV for 2 minutes and plug in again.

Troubleshooting & Tips

Tv will not turn on

Make sure the power cord is plugged in securely to

wall outlet. The batteries in the remote control may

beexhausted.PressthePowerbuttonontheTV.

Poor picture

•HaveyouselectedthecorrectTVsystem?

• Low signal level can cause picture distortion.

Pleasecheckantennaaccess.

• Check if you have entered the correct channel

frequency if you have done manual tuning.

• The picture quality may degrade when two

devices are connected to the TV at the same

time. In such a case, disconnect one of the devices.

No picture

• NoPicturemeansthatyourTV isnotreceivinga

transmission.Haveyouselectedthecorrectbutton

ontheremotecontrol?Tryoncemore.Alsomake

sure the correct input source has been selected.

•Istheantennaconnectedproperly?

•Istheantennacabledamaged?

•Aresuitableplugsusedtoconnecttheantenna?

•If you are in doubt, consult your dealer.

No sound

•HastheTVbeensettomute?Tocancelmute,press

the “ ” button, or increase the volume level.

•Sound is coming from only one speaker. Is the

balance set to one extreme? See Sound Menu

section.

Remote control - does not operate

•The batteries may be exhausted. Replace

the bateries.

Input sources - can not be selected

•If you cannot select an input source, it is possible

that no device is connected. if not

•Check the AV cables and connections if you have

tried to connect a device.

Recording unavailable

Torecordaprogramme,youshouldrstconnecta

USBdisktoyourTVwhiletheTVisswitchedoff.You

should then switch on the TV to enable recording

feature. If you cannot record, try switching off the TV

and then re-inserting the USB device.

USB is too slow

If a “USB is too slow” message is displayed on the

screen while starting a recording, try restarting

the recording. If you still get the same error, it is

possible that your USB disk does not meet the

speed requirements. Try connecting another USB

disk.

1 2 ... 24 25 26 27 28 29 30 31 32

Comentarios a estos manuales

Sin comentarios

Andersson LED2242FDC PVR Manual de usuario Pagina 29

Comentarios a estos manuales

Relacionado con productos y manuales para Televisores Lcd Andersson LED2242FDC PVR